Is Pipe Lining Worth It on Cast Iron Drain Pipes?
By Jordan Brush, owner of Speedy Piper Underground · November 11, 2026
Pipe lining can be worth it if your old cast iron is still round and still draining with proper slope. It is the wrong fix if the pipe has a belly, a collapsed or missing bottom, a separated joint, or major offsets, because the liner takes the shape of the pipe it sits inside.
Know that before signing a lining quote. A liner can form a new wall inside an old pipe. It cannot straighten a sagging pipe or put the slope back.
In Miami-Dade, Broward, and Palm Beach counties, many slab homes built before 1980 have cast iron drain lines below the floor. If you have a camera video, look at that first. The condition of the pipe on that video should decide the method.
What Pipe Lining Actually Does
Cured in place pipe lining, often called CIPP, is a resin soaked liner installed inside the existing cast iron. The liner is cured in place, forming a new pipe wall inside the old pipe. The old cast iron remains in the ground around it.
There are situations where that makes sense. An engineer, Michelle Dodroe, P.E., described CIPP as a structural reformation that can extend the lifecycle of a pipe. Trade press on lining cast iron adds that it is a good option for repairs beneath busy city streets or under historical areas.
For a relatively straight drain line that is still structurally sound and has proper fall, lining may be a reasonable repair option.
But it has limits. The same engineering guidance says CIPP cannot correct:
- A sag in the pipe
- Pipe intrusions
- Severely offset joints
- Larger holes
It also minimally reduces the interior diameter of the existing pipe. That may be a small reduction, but it is still something to discuss before work starts.
A Liner Follows the Pipe, Including Its Problems
A common belief is that lining repairs every problem without digging. A liner cannot do that.
A belly is plumber talk for a low spot in the drain line. Water and waste sit there instead of continuing downhill. The technical term is backgrade or insufficient slope. If a liner goes through that low spot, the newly lined pipe still has the same low spot, and water still sits in it.
The same goes for a pipe that has lost its bottom from corrosion. Cast iron rusts from the inside out. The wall gets thinner as scale builds inside, and the bottom of the pipe is commonly the first area to fail because that is where water runs.
Where the pipe wall is completely gone or the pipe has separated, the Florida code does not allow relining that section at all.
One customer, Alvaro C., put it plainly after comparing the choices: "I am extremely happy that I chose to replace the old cast-iron pipes rather than simply lining them."
Replacement is not automatically right for every house either, so let what the video shows settle it.
What the Florida Plumbing Code Says About Lining
The 2023 Florida Building Code, Plumbing, Section 717, puts clear limits on relining building drains.
Relining is limited to gravity drainage piping that is 4 inches in diameter and larger. The pipe must be surveyed with a recorded video camera before lining. Then the code says that where the camera inspection finds certain defects, relining is not permitted.
Those defects include:
- Backgrade or insufficient slope
- Complete pipe wall deterioration
- Complete separations, including separations from tree root invasion or improper support
When those conditions are present, the defective portions have to be exposed and repaired with pipe and fittings. The code also requires a second recorded video after the relining work is complete.
Ask for a copy of the video taken before any work, and keep it with your house papers.
The International Plumbing Code added similar relining language in its 2021 edition. Before that, the IPC did not recognize a method of pipe relining.
Why Cast Iron Under a Slab Is Often a Tougher Lining Job
A sewer line running straight across a yard to the street has few turns. The drain system under a slab house has many.
Under your floor, the main drain has branches rising to toilets, tubs, showers, sinks, and other fixtures. Each branch adds a fitting and a turn. In an older South Florida slab home, there can be a lot going on under the concrete.
Trade guidance on lining cast iron says the ideal liner job has only one change of direction. With several fittings close together, liners can have trouble making the turns, get stuck, and force excavation anyway.
So along with asking whether floors get opened, ask whether this particular pipe can be lined within code and still drain correctly.
A clean, straight section may be a fair candidate. A corroded system with missing bottoms, separated joints and bellies is a different job.
How to Read Your Camera Video Before You Sign
You do not need to be a plumber to spot the major issues on a drain camera recording. Slow the video down. Ask the person who performed the inspection to point out the defects and explain what you are seeing.
Here is what to look for.
- Standing water in the pipe: This usually points to a belly or insufficient slope. The camera may dip into water, then come back out. Lining does not remove that low spot.
- A missing bottom: You may see a dark open channel at the bottom of the cast iron, rough broken edges, or soil visible where pipe wall should be. Where the wall is gone through to the soil, that is the complete pipe wall deterioration the code lists as a condition that cannot be relined.
- A joint that has pulled apart: Watch for a gap where two pipe sections should meet. A complete separation is specifically listed in the Florida code as a condition that cannot be relined.
- Heavy rust scale: Cast iron can build up scale on the inside as it deteriorates. Ask how much usable opening remains after cleaning and after the liner is installed.
- Turns and branches: Count them. Look for toilet branches, shower branches, kitchen lines, and fittings one right after another. The more turns and connections involved, the more important it is to understand whether the liner can make that path.
- The pipe diameter: Florida's code allows relining only on gravity drainage piping 4 inches in diameter and larger. Ask which sections are proposed for lining and what size each one is, since branch lines under a slab are often smaller than the main.
Do not accept "the camera looked bad" as the whole explanation. The recorded video should show you what is being proposed and why.
Can I Decide This Myself?
You can do the first part yourself. Review the camera video, ask for the proposed scope in writing, and ask whether any bellies, missing pipe bottom, offsets, or separations were found.
You should call a qualified plumber for the decision if the video is unclear or the proposal involves relining under a slab. This is where homeowners can get hurt by comparing methods based only on whether floors will be opened.
If the pipe is sound enough for lining, a company should be able to explain why. If it is not, they should be able to show you the defect on video and explain what the code requires.
What Tunneling and Full Pipe Replacement Do Differently
For cast iron that is past the point of lining, replacement addresses the failed pipe itself. The old cast iron comes out, and new PVC goes in. PVC does not rust.
At Speedy Piper Underground, we replace failed cast iron under the slab by tunneling from outside the house with a vacuum truck. The floors and tile inside are not cut. The old cast iron is removed, new PVC is installed at full size, and it is secured to the slab with code approved stainless steel hangers.
The whole length of the tunnel is then backfilled with compressed pea gravel. The house stays in use during the work, and permits and city inspections are handled.
You can read our Compare Methods page, which sets the four methods side by side, or see How Tunneling Works.
Before you choose lining or replacement, get the drain line on camera and keep the recorded video. If you are in Miami-Dade, Broward, or Palm Beach County, Speedy Piper Underground gives free estimates. Call (786) 881-0045.
